{"id":4798,"date":"2026-08-11T14:00:42","date_gmt":"2026-08-11T06:00:42","guid":{"rendered":"https:\/\/www.graphitecutting.com\/?p=4798"},"modified":"2026-08-11T14:03:40","modified_gmt":"2026-08-11T06:03:40","slug":"graphite-kerf-loss-reduction","status":"publish","type":"post","link":"https:\/\/www.graphitecutting.com\/es\/graphite-kerf-loss-reduction\/","title":{"rendered":"How to Reduce Kerf Loss in Graphite Cutting: 5 Controllable Factors"},"content":{"rendered":"<p class=\"wp-block-paragraph\">On a 500 \u00d7 300 mm block of high-purity isotropic graphite, every additional 0.1 mm of kerf across 20 cuts translates to roughly 200 mm\u00b3 of unrecoverable material\u2014material you already paid for, and material that shows up as scrap in your monthly cost review. In high-value grades, that is not a rounding error. It is a line item.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Yet most operations trying to reduce kerf loss reach for the wrong lever first. They swap in a thinner cutting tool, run a few test cuts, see a small improvement, and stop. The problem is that tool width is only the visible part of kerf\u2014the rest is process-induced spread that a thinner tool cannot fix by itself, and sometimes makes worse.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This guide walks through the five factors that actually determine kerf loss in graphite cutting: what each one does, how they interact, and where the practical limits are. If you want the broader cost and yield perspective on why kerf matters in the first place, see the <a href=\"\/es\/corte-de-grafito-de-corte-bajo\/\">Pillar 4 overview on low-kerf graphite cutting<\/a>. This page is the operational companion.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img fetchpriority=\"high\" decoding=\"async\" width=\"1024\" height=\"576\" src=\"https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-1024x576.png\" alt=\"M\u00e1quina cortadora de grafito\" class=\"wp-image-4799\" title=\"Soluci\u00f3n de corte de grafito\" srcset=\"https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-1024x576.png 1024w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-300x169.png 300w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-768x432.png 768w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-1536x864.png 1536w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-18x10.png 18w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors-600x338.png 600w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/08\/graphite-kerf-loss-reduction-factors.png 1672w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">What Determines Kerf Loss in Graphite Cutting<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Kerf is the width of material removed by a single cut. In practice, measured kerf is always wider than the nominal tool width, because the cutting process introduces its own contribution\u2014vibration, path deviation, edge chipping, and thermal effects at the cut face. The gap between \u201ctool width\u201d and \u201cmeasured kerf\u201d is where most of your controllable loss lives.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Reducing kerf loss is therefore not a single-variable problem. It is a system problem. The five factors below are ordered roughly by how often we see them ignored, not by absolute importance. In most graphite operations, batch consistency (Factor 5) delivers more real savings than tool width (Factor 1), even though tool width gets 90% of the attention.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Factor 1: Cutting Tool Width and Stability<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Tool width matters, but stability during the cut matters more. A 0.20 mm cutting tool that deflects to an effective 0.28 mm under load produces the same kerf as a 0.28 mm tool that stays straight\u2014except the \u201cthin and unstable\u201d version usually has worse edge quality and shorter tool life.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When evaluating a cutting tool for kerf performance, look at three specifications together, not one:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Nominal width<\/strong> (the number on the spec sheet)<\/li>\n\n\n\n<li><strong>Deflection under working load<\/strong> (rarely on the spec sheet\u2014ask, or test)<\/li>\n\n\n\n<li><strong>Wear pattern over service life<\/strong> (does the tool widen uniformly, or does it develop uneven zones?)<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">The common mistake is to select the tool with the narrowest nominal width and assume kerf follows. It does not. A tool with 15% wider nominal width but half the deflection can produce a <strong>narrower and more consistent<\/strong> kerf across a full production run.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A practical rule from operations: if you cannot measure your tool\u2019s deflection under working conditions, you should not assume it matches the spec sheet. Deflection data from a bench test at room temperature tells you very little about behavior during a two-hour cut on a warm machine.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Factor 2: Feed Rate and Cutting Path Control<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Feed rate has a non-linear relationship with kerf. Push too slow and you build up heat, which widens the effective kerf through thermal spread. Push too fast and you introduce vibration and edge chipping, which also widens kerf. The optimum is a band, not a point.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Path control is the less obvious half of this factor. Even at optimal feed, a cutting path that oscillates laterally by \u00b10.05 mm produces an effective kerf that is 0.1 mm wider than the tool\u2014regardless of how narrow the tool actually is. In long cuts on large graphite blocks, path deviation is often the single largest contributor to kerf loss.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Diagnostic sequence when kerf is drifting:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Measure kerf at the start, middle, and end of a single cut<\/li>\n\n\n\n<li>If kerf widens toward the end \u2192 thermal drift, reduce feed rate or improve cooling<\/li>\n\n\n\n<li>If kerf varies mid-cut without a trend \u2192 path stability issue, check machine rigidity and any lateral load<\/li>\n\n\n\n<li>If kerf is uniform per cut but drifts across a batch \u2192 tool wear or fixture shift (see Factors 3 and 5)<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">This sequence takes 20 minutes on the shop floor. Skipping it and instead spending three days evaluating new tools is a common mistake.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Factor 3: Material Fixture and Vibration Damping<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Graphite is stiff but brittle. A fixture that cannot suppress workpiece vibration during the cut will produce kerf variation that no tool selection can compensate for. In our experience, fixture-induced kerf noise is roughly 2\u20133\u00d7 more common than tool-related kerf variation, and it is almost never the first thing operations check.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The fixture failure modes worth watching:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Insufficient clamping stiffness<\/strong> on large blocks\u2014the block flexes microscopically against the cut and the kerf tracks the flex<\/li>\n\n\n\n<li><strong>Point-load clamping<\/strong> rather than distributed clamping, which allows local rotation<\/li>\n\n\n\n<li><strong>Fixture wear over time<\/strong>\u2014clamping surfaces develop marks and lose contact area, which increases with fixture age<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">For small parts, the reverse problem appears: excessive clamping force can locally deform soft graphite grades, again shifting the effective kerf. There is no single \u201cright\u201d clamping force\u2014it depends on part geometry, graphite grade, and the cutting direction relative to the material grain.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If you inherit a fixture with a job, do not assume it is optimized. Run a kerf comparison against a temporary rigid setup before accepting the fixture\u2019s performance as baseline.<\/p>\n\n\n\n<figure class=\"wp-block-embed is-provider-youtube wp-block-embed-youtube\"><div class=\"wp-block-embed__wrapper\">\n<iframe  id=\"_ytid_36165\"  width=\"640\" height=\"360\"  data-origwidth=\"640\" data-origheight=\"360\" src=\"https:\/\/www.youtube.com\/embed\/QnALq-JjvLc?enablejsapi=1&#038;autoplay=0&#038;cc_load_policy=0&#038;cc_lang_pref=&#038;iv_load_policy=1&#038;loop=0&#038;rel=1&#038;fs=1&#038;playsinline=0&#038;autohide=2&#038;theme=dark&#038;color=red&#038;controls=1&#038;disablekb=0&#038;\" class=\"__youtube_prefs__  epyt-is-override  no-lazyload\" title=\"Reproductor de YouTube\"  allow=\"fullscreen; accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" referrerpolicy=\"strict-origin-when-cross-origin\" allowfullscreen data-no-lazy=\"1\" data-skipgform_ajax_framebjll=\"\"><\/iframe>\n<\/div><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Factor 4: Coolant and Lubrication Strategy<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Coolant does two things for kerf control: it removes heat that would otherwise widen the effective cut through thermal expansion, and it flushes cutting debris that would otherwise re-enter the kerf and widen it through secondary abrasion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Dry cutting is possible for graphite and is often used for cleanliness reasons\u2014the resulting powder is easier to collect than a slurry. But dry cutting almost always produces measurably wider kerf than wet cutting on the same material, typically by 5\u201315% depending on cut length and speed. If your operation is dry for downstream contamination reasons, that trade-off is legitimate. If it is dry because \u201cgraphite doesn\u2019t need coolant,\u201d you are paying for that assumption in kerf.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For wet cutting, the two common mistakes are:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Direcci\u00f3n incorrecta del flujo de refrigerante<\/strong> relativo a la trayectoria de corte; si el flujo no elimina los residuos de la ranura, los residuos vuelven a cortar la cara de la ranura<\/li>\n\n\n\n<li><strong>Caudal insuficiente<\/strong> para la profundidad de corte; el refrigerante necesita llegar a la zona de trabajo, no solo rociarla cerca<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">La selecci\u00f3n del refrigerante en s\u00ed importa menos de lo que la mayor\u00eda de la gente piensa, una vez que se tiene el flujo y la direcci\u00f3n correctos. La mayor\u00eda de las operaciones que vemos est\u00e1n utilizando un refrigerante adecuado con una entrega inadecuada.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Factor 5: Consistencia del proceso entre lotes<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Este es el factor que la mayor\u00eda de las operaciones descubren al final, y suele ser el que m\u00e1s ahorros genera. Reducir la ranura promedio en un 10% vale algo. Reducir la desviaci\u00f3n est\u00e1ndar de la ranura en un lote de 100 piezas en un 30% vale sustancialmente m\u00e1s, porque se traduce directamente en una menor tasa de desechos y un anidamiento posterior m\u00e1s ajustado.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">La deriva de la ranura en un lote proviene de tres fuentes:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Desgaste de la herramienta<\/strong>\u2014la herramienta de corte se ensancha gradual y predeciblemente<\/li>\n\n\n\n<li><strong>Deriva del accesorio<\/strong>\u2014las superficies de sujeci\u00f3n se desplazan micro-cantidades a medida que el accesorio se calienta<\/li>\n\n\n\n<li><strong>Degradaci\u00f3n del refrigerante<\/strong>\u2014el fluido de corte recoge residuos y su enfriamiento efectivo cambia<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">La respuesta correcta no es \u201carreglar\u201d cada fuente individualmente en el momento en que comienza a afectar la ranura. Ese es un juego perdido. La respuesta correcta es <strong>construir un proceso que tolere la deriva<\/strong> mediante:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Establecer una l\u00ednea de base de la ranura en la Pieza 1 del lote<\/li>\n\n\n\n<li>Muestrear la ranura cada N piezas (t\u00edpicamente cada 10-20 dependiendo del tama\u00f1o del lote)<\/li>\n\n\n\n<li>Establecer un umbral de deriva que active una acci\u00f3n (cambio de herramienta, refresco de refrigerante o verificaci\u00f3n del accesorio)<\/li>\n\n\n\n<li>Documentar cu\u00e1ndo se activ\u00f3 cada disparador, para construir un conjunto de datos sobre las tasas de deriva del mundo real<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">Si solo tiene tiempo para implementar una cosa de esta gu\u00eda completa, implemente el paso 3: un umbral de deriva definido y una respuesta documentada. Esto solo reduce t\u00edpicamente la varianza de la ranura a nivel de lote m\u00e1s que cualquier cambio de herramienta.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Para una mirada m\u00e1s profunda a c\u00f3mo la consistencia del lote se traduce en n\u00fameros de rendimiento, consulte la p\u00e1gina complementaria centrada en el rendimiento sobre <a href=\"\/es\/mejora-del-rendimiento-del-corte-de-grafito\/\">mejora del rendimiento del corte de grafito<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Qu\u00e9 medir y c\u00f3mo rastrear la reducci\u00f3n de la ranura<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">No necesita m\u00e1quinas de medici\u00f3n por coordenadas ni perfil\u00f3metros \u00f3pticos para establecer l\u00edneas de base de ranura \u00fatiles. Un calibrador digital calibrado o un comparador \u00f3ptico de bajo costo es suficiente para la mayor\u00eda de las operaciones de grafito, siempre que mida de manera consistente.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Las tres m\u00e9tricas que vale la pena rastrear:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Ranura media por corte<\/strong>\u2014el ancho promedio a lo largo de un solo corte<\/li>\n\n\n\n<li><strong>Desviaci\u00f3n est\u00e1ndar de la ranura dentro de un corte<\/strong>\u2014cu\u00e1nto var\u00eda la ranura a lo largo de la longitud<\/li>\n\n\n\n<li><strong>Desviaci\u00f3n est\u00e1ndar de la ranura del lote<\/strong>\u2014cu\u00e1nto var\u00eda la ranura media de pieza a pieza en un lote<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Una revisi\u00f3n semanal de estos tres n\u00fameros, graficados frente a la edad de la herramienta, la edad del refrigerante y cualquier cambio en el proceso, vale m\u00e1s que una revisi\u00f3n mensual de una docena de m\u00e9tricas adicionales. La complejidad no es lo que mejora la ranura. La medici\u00f3n consistente lo hace.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Una sugerencia pr\u00e1ctica: rastree la ranura en un gr\u00e1fico de pared, no solo en una base de datos. Un gr\u00e1fico visible en el taller cambia el comportamiento del operador de una manera que un informe de base de datos no lo hace. La disciplina de medici\u00f3n se refuerza a s\u00ed misma cuando es visible.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Cu\u00e1ndo no perseguir una ranura m\u00e1s baja<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">No todas las operaciones de grafito se benefician de una reducci\u00f3n agresiva de la ranura. Si el costo de su pieza est\u00e1 dominado por el tiempo de mecanizado posterior, y el costo del material por pieza es una peque\u00f1a parte del costo total, entonces reducir la ranura en un 20% puede reducir el costo total solo en un 2-3%. Eso es real, pero puede que no justifique la inversi\u00f3n en el proceso.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Las operaciones que m\u00e1s se benefician de una reducci\u00f3n seria de la ranura comparten tres caracter\u00edsticas:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>El costo del material es una parte significativa del costo total de la pieza (t\u00edpicamente 30%+)<\/li>\n\n\n\n<li>Los tama\u00f1os de lote son lo suficientemente grandes como para que la consistencia importe<\/li>\n\n\n\n<li>Los procesos posteriores no pueden recuperarse f\u00e1cilmente de la variaci\u00f3n de la ranura (es decir, no hay un paso de acabado indulgente)<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Si cumple las tres, los factores de esta gu\u00eda se aplican directamente. Si solo cumple una, tenga cuidado con cu\u00e1nto invierte en la reducci\u00f3n de la ranura frente a otras palancas de rendimiento.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Lectura relacionada<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><a href=\"\/es\/corte-de-grafito-de-corte-bajo\/\">Corte de Grafito de Bajo Kerf: P\u00e9rdida de Material, Rendimiento e Impacto en el Costo de Fabricaci\u00f3n<\/a> \u2014 la perspectiva de costos y econ\u00f3mica sobre por qu\u00e9 importa la ranura<\/li>\n\n\n\n<li><a href=\"\/es\/mejora-del-rendimiento-del-corte-de-grafito\/\">Mejora del rendimiento del corte de grafito<\/a> \u2014 c\u00f3mo el control de la ranura se conecta con el rendimiento general<\/li>\n\n\n\n<li><a href=\"\/es\/perdida-de-material-en-el-mecanizado-de-grafito\/\">P\u00e9rdida de material en el mecanizado de grafito<\/a> \u2014 comparaci\u00f3n de la p\u00e9rdida de ranura con la eliminaci\u00f3n de virutas en el mecanizado<\/li>\n\n\n\n<li><a href=\"\/es\/corte-de-grafito-de-precision-2\/\">Precision Graphite Slicing<\/a> \u2014 proceso relacionado para aplicaciones de corte de alta precisi\u00f3n<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>","protected":false},"excerpt":{"rendered":"<p>On a 500 \u00d7 300 mm block of high-purity isotropic graphite, every additional 0.1 mm of kerf across 20 cuts translates to roughly 200 mm\u00b3 of unrecoverable material\u2014material you already paid for, and material that shows up as scrap in your monthly cost review. In high-value grades, that is not a rounding error. It is [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":4799,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[371],"tags":[839,375,841,840,842],"class_list":["post-4798","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-graphite-cutting-technology","tag-cost-optimization","tag-graphite-cutting","tag-graphite-kerf-loss","tag-kerf-reduction","tag-process-control"],"_links":{"self":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts\/4798","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/comments?post=4798"}],"version-history":[{"count":3,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts\/4798\/revisions"}],"predecessor-version":[{"id":4802,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts\/4798\/revisions\/4802"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/media\/4799"}],"wp:attachment":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/media?parent=4798"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/categories?post=4798"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/tags?post=4798"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}