{"id":4932,"date":"2026-11-21T18:00:00","date_gmt":"2026-11-22T02:00:00","guid":{"rendered":"https:\/\/www.graphitecutting.com\/?p=4932"},"modified":"2026-11-19T17:26:50","modified_gmt":"2026-11-20T01:26:50","slug":"graphite-slab-cutting-from-large-blocks","status":"publish","type":"post","link":"https:\/\/www.graphitecutting.com\/es\/graphite-slab-cutting-from-large-blocks\/","title":{"rendered":"Corte de Placas de Grafito a Partir de Bloques Grandes: Plan de Soporte, Corte y Tolerancia de Placa"},"content":{"rendered":"<nav aria-label=\"Table of contents\"><h2>Contents<\/h2><ul><li><a href=\"#section-1\">Five Pre-Trial Checks<\/a><\/li><li><a href=\"#section-2\">Specify the Blank for Graphite Slab Cutting from Large Blocks<\/a><\/li><li><a href=\"#section-3\">Design the Separation Sequence Around the Cut-Off Section<\/a><\/li><li><a href=\"#section-4\">Where the SHG Top-Down Operation Fits<\/a><\/li><li><a href=\"#section-5\">Set Graphite Slab Cutting from Large Blocks Apart from Thin Slicing<\/a><\/li><li><a href=\"#section-6\">Plan Material for Graphite Slab Cutting from Large Blocks<\/a><\/li><li><a href=\"#section-7\">Keep Wire Speed and Feed Rate Distinct<\/a><\/li><li><a href=\"#section-8\">Inspect Graphite Slab Cutting from Large Blocks at Handover<\/a><\/li><li><a href=\"#section-9\">Field Notes: A Bar Trial Cannot Certify a Slab Route<\/a><\/li><li><a href=\"#section-10\">Known Limitations \/ Trade-offs<\/a><\/li><li><a href=\"#section-11\">Preguntas frecuentes<\/a><\/li><\/ul><\/nav>\n\n\n\n<p class=\"wp-block-paragraph\">Graphite slab cutting from large blocks needs a plan for both the retained stock and the section that becomes free. A straight cutting path is only part of the job: the separated slab must remain controlled, and the blank must retain enough material for its next operation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Define the required output before selecting the cut position. A thick plate blank for later machining is a different deliverable from a finished thin sheet. Thickness, face condition, datum requirements and handling access should be written into the trial request rather than inferred from an attractive cut surface.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">En <a href=\"https:\/\/www.graphitecutting.com\/es\/corte-de-bloques-de-grafito-industrial\/\">large-block cutting topic page<\/a> covers the broader initial-division route. This article stays with slab separation, support and handover; the <a href=\"https:\/\/www.graphitecutting.com\/es\/corte-de-grafito-de-precision-2\/\">gu\u00eda de corte de grafito de precisi\u00f3n<\/a> addresses the separate thin-slicing discussion.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-1\">Five Pre-Trial Checks<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Use these five checks as an index to the detailed review below. They organize the proposed job; they are not a claim of measured SHG performance.<\/p>\n\n\n\n<ol><li>Define the required slab blank.<\/li><li>Support retained and separated stock.<\/li><li>Plan the removal path.<\/li><li>Reserve the agreed finishing stock.<\/li><li>Inspect the blank after separation.<\/li><\/ol>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-2\">Specify the Blank for Graphite Slab Cutting from Large Blocks<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Keep the incoming stock dimensions, slab blank dimensions and finished component dimensions separate. The first operation may deliberately leave additional material for establishing reference faces or finishing the thickness later. Do not remove that material simply to make the cut blank resemble the final drawing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Identify which face will locate in the next fixture. Then mark which opposite face carries the remaining thickness allowance. Where the route includes several slabs from one block, give every proposed blank a location on the cut sketch so the cumulative material requirement can be reviewed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">La identificaci\u00f3n del material se mantiene con el plano. <a href=\"https:\/\/www.sglcarbon.com\/en\/markets-solutions\/material\/sigrafine-isostatic-graphite\/\" rel=\"nofollow noopener\" target=\"_blank\">La informaci\u00f3n de grafito isost\u00e1tico de SGL Carbon<\/a> explica que los grados tienen propiedades distintas. Un resultado de corte anterior en una familia de existencias no califica autom\u00e1ticamente a todos los grados suministrados ni a todas las secciones.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Indique si la losa se acepta directamente despu\u00e9s de la separaci\u00f3n o solo despu\u00e9s de una operaci\u00f3n de acabado posterior. Esa decisi\u00f3n afecta el plan de medici\u00f3n, el material reservado y lo que el equipo de recepci\u00f3n puede esperar leg\u00edtimamente del tocho.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-3\">Design the Separation Sequence Around the Cut-Off Section<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Dibuje el bloque retenido y la losa que se separar\u00e1, incluidas sus ubicaciones de soporte. Revise la etapa final del corte antes de comenzar. El soporte que es adecuado mientras el material es continuo puede no controlar la pieza una vez que desaparece la conexi\u00f3n restante.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">La revisi\u00f3n del proceso debe identificar la masa, la orientaci\u00f3n y el m\u00e9todo de extracci\u00f3n previsto de la secci\u00f3n separada. No asuma que el alambre de corte lo sujetar\u00e1 despu\u00e9s de la separaci\u00f3n, y no trate una superficie de mesa cercana como un soporte aprobado sin verificar la disposici\u00f3n real.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Haga que la ruta de extracci\u00f3n sea parte de la revisi\u00f3n del utillaje. Una losa puede caber en el sobre de corte, pero ser dif\u00edcil de extraer con el equipo disponible. El acceso para la elevaci\u00f3n, el estado del material restante y el espacio libre alrededor de los conjuntos de corte deben acordarse antes de la prueba.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Mantenga las decisiones de manipulaci\u00f3n dentro de los procedimientos aprobados y los l\u00edmites de equipo del sitio. La capacidad de elevaci\u00f3n, el espaciado de los soportes o la clasificaci\u00f3n de carga del utillaje no se pueden establecer solo a partir de la fotograf\u00eda SHG. Solicite los valores faltantes para el bloque y la instalaci\u00f3n reales.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-4\">Where the SHG Top-Down Operation Fits<\/h2>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1.jpg\" alt=\"Graphite slab cutting from large blocks: cylindrical stock at separation\" class=\"wp-image-4914\" width=\"1378\" height=\"1400\" style=\"width:100%;height:auto;max-height:640px;object-fit:contain\" title=\"Soluci\u00f3n de corte de grafito\" srcset=\"https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1.jpg 1378w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1-295x300.jpg 295w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1-1008x1024.jpg 1008w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1-768x780.jpg 768w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1-12x12.jpg 12w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-d9b0fb24bff1-600x610.jpg 600w\" sizes=\"auto, (max-width: 1378px) 100vw, 1378px\" \/><figcaption class=\"wp-element-caption\">Figura 1. Una l\u00ednea de corte en material cil\u00edndrico en la recomendaci\u00f3n de origen. \u00daselo como contexto de separaci\u00f3n; no documenta la secuencia completa de soporte y extracci\u00f3n de la losa.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The public product description associates Z movement with top-down feed for slabbing and section separation. Separate cutting assemblies operate above a low, stationary table. The intended cut orientation should be confirmed on the setup drawing rather than inferred solely from the direction words in a video title.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Review the <a href=\"https:\/\/www.graphitecutting.com\/es\/maquina-de-corte-de-bloques-de-grafito-grandes-shg\/\">SHG slab and plate cutting configurations<\/a> after defining the operation. SHG330-120 lists a nominal 3,300 \u00d7 1,200 \u00d7 1,000 mm envelope in a single direction, while the combined envelope is 2,500 \u00d7 1,200 \u00d7 1,000 mm.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the slab route also requires trimming in the other direction without relocating the stock, the shorter combined envelope becomes relevant. Do not quote the single-mode length as the accepted size for a two-direction setup.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For SHG300-170, the horizontal-only envelope is listed as 3,000 \u00d7 1,700 \u00d7 1,400 mm, whereas the combined column lists 2,400 \u00d7 1,400 mm with height to confirm. Those are nominal configuration dimensions, not demonstrated slab-thickness capability or allowable load.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Video: Gantry block slicing<\/h3>\n\n\n\n<iframe width=\"360\" height=\"640\" style=\"width:100%;max-width:360px;aspect-ratio:9\/16;height:auto;border:0;display:block;margin:0 auto\" src=\"https:\/\/www.youtube.com\/embed\/ff2F7ArRhSo?rel=0\" title=\"Graphite Block Slicing | Gantry Wire Saw Machine\" loading=\"lazy\" referrerpolicy=\"strict-origin-when-cross-origin\" allow=\"encrypted-media; picture-in-picture; fullscreen\" allowfullscreen><\/iframe>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.youtube.com\/watch?v=ff2F7ArRhSo\" rel=\"nofollow noopener\" target=\"_blank\">Watch on YouTube<\/a> \u00b7 Vimfun Endless Diamond Wire Saw<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This gantry block-slicing reference provides process context for graphite slab cutting from large blocks. Exact model, slab thickness, complete cut-off support and post-removal dimensions are not verified by the clip; qualify those details against the proposed job.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-5\">Set Graphite Slab Cutting from Large Blocks Apart from Thin Slicing<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The distinction is the required output and acceptance route, not a universal thickness threshold supplied here. A slab blank may carry stock for later face correction, while a thin-slicing job may place a different emphasis on thickness distribution and handling of each sheet.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Avoid using a thin-sheet demonstration to validate a thick-slab setup. The stock section, support and removal conditions may be different even if both processes use diamond wire. Likewise, a video of a large block being separated does not establish the thinnest acceptable sheet.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When the slab will become feedstock for later slicing, coordinate its reference surfaces and dimensions with that next operation. The first cutting team should know which face must remain usable for locating and how much material the slicing route needs.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This boundary prevents two misleading substitutions: using a thin-slice claim as a slab acceptance result, or using a slab-cut photograph as proof of precision sheet production. Each route needs evidence matched to its actual deliverable.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Video: A separate multi-wire slicing route<\/h3>\n\n\n\n<iframe width=\"360\" height=\"640\" style=\"width:100%;max-width:360px;aspect-ratio:9\/16;height:auto;border:0;display:block;margin:0 auto\" src=\"https:\/\/www.youtube.com\/embed\/wqykRx5FmFY?rel=0\" title=\"Graphite Multi-Wire Slicing | Wire Saw Machine\" loading=\"lazy\" referrerpolicy=\"strict-origin-when-cross-origin\" allow=\"encrypted-media; picture-in-picture; fullscreen\" allowfullscreen><\/iframe>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.youtube.com\/watch?v=wqykRx5FmFY\" rel=\"nofollow noopener\" target=\"_blank\">Watch on YouTube<\/a> \u00b7 Vimfun Endless Diamond Wire Saw<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Several wires cut graphite stock together in this multi-wire reference. This is a separate slicing arrangement, not evidence that the standard SHG uses multiple wires per cutting assembly. Compare it only as a different route; no slab tolerance, accepted output or production-rate advantage is established here.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-6\">Plan Material for Graphite Slab Cutting from Large Blocks<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Build a cut sketch that accounts for retained blanks, planned finishing stock, separation losses and unusable edges. Use the actual qualified kerf allowance where available. Wire diameter and slab thickness are not interchangeable with measured material loss.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For repeated slabs, review the cumulative requirement rather than checking only the first blank. A route that leaves sufficient stock at the beginning can produce an undersized final remainder if the layout ignores losses between sections.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Do not assign an attractive recovery percentage to the drawing alone. Accepted output depends on whether the separated blanks survive handling and meet the agreed geometry and edge requirements. Keep nominal layout efficiency separate from accepted material recovery.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the process data are incomplete, show the unresolved terms on the planning sheet. This is more useful than inserting a guessed kerf or allowance and presenting the result as a validated production plan.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-7\">Keep Wire Speed and Feed Rate Distinct<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The SHG product page lists a machine wire-speed range of 0\u201350 m\/s. It separately gives initial isostatic and fine-grain graphite windows of 30\u201340 m\/s wire speed and 50\u2013100 mm\/min feed. These are manufacturer starting recommendations, not measurements from the proposed slab job.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Wire speed describes circulation of the cutting wire; feed describes the relative advance of the cutting assembly through the material. Increasing one does not mean the other has increased. Record both with their units on the trial sheet.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For graphite slab cutting from large blocks, select commissioning conditions against the actual grade, section and support arrangement. This article supplies no universal production setting, guaranteed cutting time or optimum feed for a particular slab thickness.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-8\">Inspect Graphite Slab Cutting from Large Blocks at Handover<\/h2>\n\n\n\n<figure class=\"wp-block-image size-full\"><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa.jpg\" alt=\"Graphite slab cutting from large blocks: rectangular stock under a cutting head\" class=\"wp-image-4915\" width=\"1394\" height=\"1400\" style=\"width:100%;height:auto;max-height:640px;object-fit:contain\" title=\"Soluci\u00f3n de corte de grafito\" srcset=\"https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa.jpg 1394w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-300x300.jpg 300w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-1020x1024.jpg 1020w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-150x150.jpg 150w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-768x771.jpg 768w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-12x12.jpg 12w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-600x603.jpg 600w, https:\/\/www.graphitecutting.com\/wp-content\/uploads\/2026\/11\/vimfun-shg-9533a2855caa-100x100.jpg 100w\" sizes=\"auto, (max-width: 1394px) 100vw, 1394px\" \/><figcaption class=\"wp-element-caption\">Figure 2. Rectangular stock beneath a cutting head in the source recommendation. Actual support load and the proposed cut-off arrangement still need confirmation.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Measure the blank where the drawing and receiving fixture require it. Record thickness distribution, relevant face relationships and edge condition separately. A visual surface check should not be converted into a numerical roughness or flatness result.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Explain the inspection support and orientation. If the blank is moved to a different support for measurement, preserve that detail so a later difference is not automatically attributed to the cutting process. Identify the surfaces used as references rather than calling every face a datum.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/www.itl.nist.gov\/div898\/handbook\/mpc\/section5\/mpc5.htm\" rel=\"nofollow noopener\" target=\"_blank\">NIST\u2019s uncertainty analysis guidance<\/a> supports matching the measurement to the acceptance decision. More display digits do not establish that a shop-floor method resolves the required feature throughout a large blank.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Keep this inspection attached to the blank identity. The receiving operation needs the individual results and remaining allowances, not merely a message that the slab was cut successfully.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-9\">Field Notes: A Bar Trial Cannot Certify a Slab Route<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">En <a href=\"https:\/\/www.graphitecutting.com\/es\/corte-de-bloque-de-grafito-isostatico\/\">documented isostatic graphite trial<\/a> produced one nominal 500 \u00d7 87 \u00d7 70 mm bar on an SVI250-80. Reported thickness readings ranged from 69.90 to 70.10 mm; width readings increased from 87.00 to 87.30 mm with wire-diameter compensation disabled.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Those readings show why individual positions and settings matter to a blank handover. They do not establish SHG slab thickness, support behavior or the condition of a plate after removal. The available record is a different machine and workpiece geometry.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">No SHG trial containing the full slab support arrangement, cut-off sequence and post-removal measurement map is supplied here. Graphite slab cutting from large blocks therefore remains a route to qualify against the drawing, rather than a measured capability claim inferred from that bar.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-10\">Known Limitations \/ Trade-offs<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Graphite slab cutting from large blocks is not complete when the wire exits the material. The blank must be controlled, identified and accepted at the specified stage. Nominal machine capacity does not establish lifting capacity, finished thickness, face accuracy or a universal handling arrangement.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Additional stock can preserve finishing options but consumes material. Reducing stock can improve nominal layout efficiency while leaving insufficient room to correct a face or remove an unacceptable edge. Agree on the trade-off with the next machining operation before finalizing the cut sketch.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Keeping the stock stationary may suit the planned separation route, but quantified handling savings or improved flatness require a matched comparison. Neither the product layout nor the process video supplies that result.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"section-11\">Preguntas frecuentes<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">What should graphite slab cutting from large blocks prove first?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The trial should show that representative stock can be separated with the proposed support and removal method, leaving a blank that meets the agreed handover requirements. Record the complete sequence and inspection conditions.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Can a good-looking slab go straight to final use?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Only when the drawing and acceptance record permit that delivery state. Otherwise preserve the finishing operations, locating requirements and machining stock in the route. Appearance is a useful observation, but it is not a release certificate.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Does graphite slab cutting from large blocks qualify thin-sheet production?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. The deliverable and acceptance route must be matched to the trial. A separated slab can be feedstock for another operation without proving the thickness control or handling of thin sheets. Keep the later slicing requirements in the route.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Can wire diameter be used directly as the layout loss?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Do not substitute it for a qualified kerf allowance. The cut sketch should use the measured or otherwise approved separation allowance for the intended process. Where that information is absent, leave the loss term unresolved rather than presenting a calculated recovery figure as validated.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Which support arrangement should be recorded during inspection?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Record how the slab is supported and oriented when the measurements are taken. If that differs from the cutting setup, preserve the distinction. Otherwise a later difference in the readings may be attributed to cutting without evidence that the inspection conditions were comparable.<\/p>","protected":false},"excerpt":{"rendered":"<p>Plan de corte de placas de grafito a partir de bloques grandes con separaci\u00f3n controlada, soportes y tolerancia de placa. Definir la inspecci\u00f3n y el siguiente proceso antes de las pruebas.<\/p>","protected":false},"author":1,"featured_media":4914,"comment_status":"closed","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"disabled","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[371],"tags":[],"class_list":["post-4932","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-graphite-cutting-technology"],"_links":{"self":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts\/4932","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/comments?post=4932"}],"version-history":[{"count":1,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts\/4932\/revisions"}],"predecessor-version":[{"id":4933,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/posts\/4932\/revisions\/4933"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/media\/4914"}],"wp:attachment":[{"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/media?parent=4932"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/categories?post=4932"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.graphitecutting.com\/es\/wp-json\/wp\/v2\/tags?post=4932"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}