Slab and plate cutting
Feed the cutting head down through the block to separate slabs or part off sections.

La série SHG découpe de grands blocs de graphite en dalles, plaques et ébauches profilées. Des têtes de coupe horizontales et verticales séparées se déplacent au-dessus d'une table basse stationnaire, de sorte que le bloc puisse rester dans la même configuration lors du changement de direction de coupe.
Choisissez parmi quatre modèles standard en fonction du mode de coupe requis et des dimensions complètes du bloc. La capacité standard atteint 3 300 mm en mode simple et 2 500 mm en mode combiné.
Utilisez la SHG comme machine de sciage de blocs de graphite pour des coupes droites. Comparez les enveloppes de travail pour la coupe horizontale et verticale du graphite avant de choisir un modèle.
La démonstration de la série Vimfun couvre trois modes de coupe dans une seule configuration. Utilisez-la pour examiner le positionnement de la pièce et le mouvement de la tête de coupe, ainsi que le tableau de capacité des modèles.
Vérifiez les dimensions complètes de votre bloc par rapport au mode de coupe que vous prévoyez d'utiliser. Les dimensions sont en millimètres, indiquées comme longueur × largeur × hauteur.
| Modèle | Horizontal uniquement | Vertical uniquement | Horizontal + vertical combiné |
|---|---|---|---|
| SHG250-120 | 2500 × 1200 × 1000 | 2500 × 1200 × 1000 | 1800 × 1200 × 1000 |
| SHG280-140 | 2800 × 1400 × 1400 | 2800 × 1400 × confirmer H | 2200 × 1400 × confirmer H |
| SHG300-170 | 3000 × 1700 × 1400 | 3000 × 1700 × confirmer H | 2400 × 1400 × confirmer H |
| SHG330-120 | 3300 × 1200 × 1000 | 3300 × 1200 × 1000 | 2500 × 1200 × 1000 |
Confirmer H signifie que la hauteur disponible nécessite une révision de la configuration. Les dimensions sont nominales et sujettes à confirmation de commande.
| Spécifications | SHG250-120 | SHG280-140 | SHG300-170 | SHG330-120 |
|---|---|---|---|---|
| Course X / Y / Z (mm) | 2500 / 1000 / 1000 | 2800 / 1400 / 1400 | 3000 / 1400 / 1400 | 3300 / 1000 / 1000 |
| Table de travail (mm) | 2500 × 1000 | 2800 × 1000 | 3000 × 1000 | 3300 × 1000 |
| Machine weight, approx. (kg) | 4200 | 4500 | 4650 | 4400 |
| Overall dimensions, approx. (m) | 3.9 × 2.3 × 2.45 | 4.2 × 2.45 × 2.5 | 4.2 × 2.8 × 2.5 | 4.5 × 2.8 × 2.5 |
Standard supply is AC 380 V, three-phase. Installed power is approximately 9 kW. Machine weights exclude packing. Confirm workpiece support and table load for your block.
The SHG holds the graphite block stationary on a low table. Two independent cutting assemblies move on the gantry, each with its own closed-loop cutting wire. The numbers in the schematic match the component list below.
| Axis | Arrow in schematic | What moves | Fonction |
|---|---|---|---|
| X | Front to back, along the block length | Cutting assemblies travel front to back along the block length; both units share this longitudinal travel. | Squaring, trimming and long straight cuts. |
| Y | Left to right, across the block width (along the beam) | Cutting assemblies move across the width of the workpiece. | Positionnement de la coupe sur la largeur du bloc. |
| Z | Verticale | Déplacement vertical de l'ensemble de coupe. | Alimentation de haut en bas pour le débitage et la séparation des sections. |
| X + Z | Mouvement coordonné | Les deux axes se déplacent en même temps sous le contrôle de la CNC. | Programmed contour cuts for shaped blanks. |
Share the profile drawing so Vimfun can confirm feasibility and fixture clearance.
m/s. How fast the closed-loop wire circulates around its loop. It is set by the wire drive.
Machine range: 0–50 m/s. Initial window for isostatic and fine-grain graphite: 30–40 m/s.
mm/min. How fast CNC motion advances the cutting assembly relative to the block, which is how fast the cut progresses through the graphite.
Machine range: X 0.01–3000 mm/min; Y and Z 0.01–5000 mm/min. Initial window for isostatic and fine-grain graphite: 50–100 mm/min.
Wire speed is the motion of the cutting tool itself. Feed rate is the motion of the axes. At the initial window, the wire travels roughly 18,000 to 48,000 times farther per minute than the head advances. Raising wire speed does not advance the cut, and raising feed does not make the wire run faster. Set both during commissioning for the actual grade and section size.
Single-mode length matches the X travel of the model. When the horizontal and vertical units work in the same setup, both assemblies share the same X stroke instead of each having the full stroke. The block must therefore fit a shorter envelope. On the standard models, the combined-mode length is 600 to 800 mm below the single-mode length.
A 2,400 × 1,400 × 1,200 mm block requiring both directions puts the SHG300-170 on the shortlist. Its combined-mode length and width match the nominal block size. Confirm usable height, actual stock dimensions and support clearance before selecting it. The SHG330-120 has a 1,200 mm combined-mode width, so this block exceeds its width limit.

Locate the block from a stable datum, check support under the cut-off section, and allow space for dust extraction and handling before the first pass.
Feed the cutting head down through the block to separate slabs or part off sections.
Cut along the block length to trim edges and prepare stock for downstream machining.
Use coordinated X/Z motion to cut a programmed profile for shaped graphite blanks.
These images come from the SHG equipment recommendation. Use them with the capacity table when checking the intended operation.





Agree on the finished blank dimensions and machining allowance before selecting feed or cutting direction. Inspect the reference face, edge condition and dimensional variation at agreed positions. Record graphite grade, cut orientation and support to make the result repeatable.
Typical materials include isostatic, extruded and fine-grain graphite. The SHG series cuts graphite dry. Plan dust extraction at the cutting zone and confirm workpiece support and fixturing for your block dimensions.
For isostatic and fine-grain graphite, the initial process window is 30–40 m/s wire speed and 50–100 mm/min feed. Initial wire diameter and tension ranges are 0.6–1.0 mm and 150–200 N. The machine wire speed range is 0–50 m/s. Set production parameters during commissioning for the actual grade and section size.
The SHG330-120 accommodates a block up to 3,300 mm long in either single cutting mode, with a nominal envelope of 3,300 × 1,200 × 1,000 mm. Its combined-mode length limit is 2,500 mm.
Yes. The separate cutting units are mounted on one frame. Check the combined-mode envelope for the selected model before committing to the cut plan.
Coordinated X/Z interpolation supports programmed contour cuts. Share the profile drawing to confirm feasibility.
The SHG graphite process is dry. Provide dust extraction at the cutting zone.
X, Y and Z travel, worktable dimensions, fixturing and dust extraction interfaces can be specified to suit the installation.
Discuss your SHG configuration
Request an SHG quote