Schneiden von Blöcken und Platten
Führen Sie den Schneidkopf durch den Block, um Blöcke zu trennen oder Abschnitte abzutrennen.

The SHG series cuts large graphite blocks into slabs, plates and profiled blanks. Separate horizontal and vertical cutting heads travel above a low, stationary table, so the block can stay in the same setup when switching cutting directions.
Choose from four standard models by the required cutting mode and full block dimensions. Standard capacity reaches 3,300 mm in a single mode and 2,500 mm in combined mode.
Use the SHG as a graphite block slabbing machine for straight cuts. Compare the working envelopes for horizontal and vertical graphite cutting before choosing a model.
Vimfun’s series demonstration covers three cutting modes in one setup. Use it to review workpiece positioning and cutting-head movement alongside the model capacity table.
Check your full block dimensions against the cutting mode you plan to use. Dimensions are in millimetres, listed as length × width × height.
| Modell | Horizontal only | Vertical only | Combined horizontal + vertical |
|---|---|---|---|
| SHG250-120 | 2500 × 1200 × 1000 | 2500 × 1200 × 1000 | 1800 × 1200 × 1000 |
| SHG280-140 | 2800 × 1400 × 1400 | 2800 × 1400 × confirm H | 2200 × 1400 × confirm H |
| SHG300-170 | 3000 × 1700 × 1400 | 3000 × 1700 × confirm H | 2400 × 1400 × confirm H |
| SHG330-120 | 3300 × 1200 × 1000 | 3300 × 1200 × 1000 | 2500 × 1200 × 1000 |
Confirm H means the available height needs configuration review. Dimensions are nominal and subject to order confirmation.
| Spezifikation | SHG250-120 | SHG280-140 | SHG300-170 | SHG330-120 |
|---|---|---|---|---|
| X / Y / Z travel (mm) | 2500 / 1000 / 1000 | 2800 / 1400 / 1400 | 3000 / 1400 / 1400 | 3300 / 1000 / 1000 |
| Worktable (mm) | 2500 × 1000 | 2800 × 1000 | 3000 × 1000 | 3300 × 1000 |
| Machine weight, approx. (kg) | 4200 | 4500 | 4650 | 4400 |
| Overall dimensions, approx. (m) | 3.9 × 2.3 × 2.45 | 4.2 × 2.45 × 2.5 | 4.2 × 2.8 × 2.5 | 4.5 × 2.8 × 2.5 |
Standard supply is AC 380 V, three-phase. Installed power is approximately 9 kW. Machine weights exclude packing. Confirm workpiece support and table load for your block.
The SHG holds the graphite block stationary on a low table. Two independent cutting assemblies move on the gantry, each with its own closed-loop cutting wire. The numbers in the schematic match the component list below.
| Axis | Arrow in schematic | What moves | Function |
|---|---|---|---|
| X | Front to back, along the block length | Cutting assemblies travel front to back along the block length; both units share this longitudinal travel. | Squaring, trimming and long straight cuts. |
| Y | Left to right, across the block width (along the beam) | Cutting assemblies move across the width of the workpiece. | Positioning the cut across the width of the block. |
| Z | Vertikal | Vertical travel of the cutting assembly. | Top-down feed for slabbing and separating sections. |
| X + Z | Coordinated motion | Both axes move at the same time under CNC control. | Programmed contour cuts for shaped blanks. |
Share the profile drawing so Vimfun can confirm feasibility and fixture clearance.
m/s. How fast the closed-loop wire circulates around its loop. It is set by the wire drive.
Machine range: 0–50 m/s. Initial window for isostatic and fine-grain graphite: 30–40 m/s.
mm/min. How fast CNC motion advances the cutting assembly relative to the block, which is how fast the cut progresses through the graphite.
Machine range: X 0.01–3000 mm/min; Y and Z 0.01–5000 mm/min. Initial window for isostatic and fine-grain graphite: 50–100 mm/min.
Wire speed is the motion of the cutting tool itself. Feed rate is the motion of the axes. At the initial window, the wire travels roughly 18,000 to 48,000 times farther per minute than the head advances. Raising wire speed does not advance the cut, and raising feed does not make the wire run faster. Set both during commissioning for the actual grade and section size.
Die Einzellängenlänge entspricht der X-Bewegung des Modells. Wenn die horizontalen und vertikalen Einheiten im selben Setup arbeiten, teilen sich beide Baugruppen denselben X-Hub anstelle des vollen Hubs für jede. Der Block muss daher in ein kürzeres Gehäuse passen. Bei den Standardmodellen ist die kombinierte Länge 600 bis 800 mm kürzer als die Einzellänge.
Ein 2.400 × 1.400 × 1.200 mm großer Block, der beide Richtungen benötigt, bringt den SHG300-170 auf die engere Wahl. Seine kombinierte Länge und Breite entsprechen der nominalen Blockgröße. Bestätigen Sie die nutzbare Höhe, die tatsächlichen Lagerabmessungen und den Stützabstand, bevor Sie ihn auswählen. Der SHG330-120 hat eine kombinierte Breite von 1.200 mm, sodass dieser Block seine Breitenbegrenzung überschreitet.

Positionieren Sie den Block von einem stabilen Bezugspunkt aus, überprüfen Sie die Unterstützung unter dem abgeschnittenen Teil und lassen Sie Platz für die Staubabsaugung und Handhabung vor dem ersten Durchgang.
Führen Sie den Schneidkopf durch den Block, um Blöcke zu trennen oder Abschnitte abzutrennen.
Schneiden Sie entlang der Blocklänge, um Kanten zu besäumen und das Material für die nachfolgende Bearbeitung vorzubereiten.
Verwenden Sie die koordinierte X/Z-Bewegung, um ein programmiertes Profil für geformte Graphitrohlinge zu schneiden.
These images come from the SHG equipment recommendation. Use them with the capacity table when checking the intended operation.





Agree on the finished blank dimensions and machining allowance before selecting feed or cutting direction. Inspect the reference face, edge condition and dimensional variation at agreed positions. Record graphite grade, cut orientation and support to make the result repeatable.
Typical materials include isostatic, extruded and fine-grain graphite. The SHG series cuts graphite dry. Plan dust extraction at the cutting zone and confirm workpiece support and fixturing for your block dimensions.
For isostatic and fine-grain graphite, the initial process window is 30–40 m/s wire speed and 50–100 mm/min feed. Initial wire diameter and tension ranges are 0.6–1.0 mm and 150–200 N. The machine wire speed range is 0–50 m/s. Set production parameters during commissioning for the actual grade and section size.
The SHG330-120 accommodates a block up to 3,300 mm long in either single cutting mode, with a nominal envelope of 3,300 × 1,200 × 1,000 mm. Its combined-mode length limit is 2,500 mm.
Yes. The separate cutting units are mounted on one frame. Check the combined-mode envelope for the selected model before committing to the cut plan.
Coordinated X/Z interpolation supports programmed contour cuts. Share the profile drawing to confirm feasibility.
The SHG graphite process is dry. Provide dust extraction at the cutting zone.
X, Y and Z travel, worktable dimensions, fixturing and dust extraction interfaces can be specified to suit the installation.
Discuss your SHG configuration
Request an SHG quote