Slab and plate cutting
Feed the cutting head down through the block to separate slabs or part off sections.

The SHG series cuts large graphite blocks into slabs, plates and profiled blanks. Separate horizontal and vertical cutting heads travel above a low, stationary table, so the block can stay in the same setup when switching cutting directions.
Choose from four standard models by the required cutting mode and full block dimensions. Standard capacity reaches 3,300 mm in a single mode and 2,500 mm in combined mode.
Use the SHG as a graphite block slabbing machine for straight cuts. Compare the working envelopes for horizontal and vertical graphite cutting before choosing a model.
Vimfun’s series demonstration covers three cutting modes in one setup. Use it to review workpiece positioning and cutting-head movement alongside the model capacity table.
Check your full block dimensions against the cutting mode you plan to use. Dimensions are in millimetres, listed as length × width × height.
| モデル | Horizontal only | Vertical only | Combined horizontal + vertical |
|---|---|---|---|
| SHG250-120 | 2500 × 1200 × 1000 | 2500 × 1200 × 1000 | 1800 × 1200 × 1000 |
| SHG280-140 | 2800 × 1400 × 1400 | 2800 × 1400 × confirm H | 2200 × 1400 × confirm H |
| SHG300-170 | 3000 × 1700 × 1400 | 3000 × 1700 × confirm H | 2400 × 1400 × confirm H |
| SHG330-120 | 3300 × 1200 × 1000 | 3300 × 1200 × 1000 | 2500 × 1200 × 1000 |
Confirm H means the available height needs configuration review. Dimensions are nominal and subject to order confirmation.
| 仕様 | SHG250-120 | SHG280-140 | SHG300-170 | SHG330-120 |
|---|---|---|---|---|
| X / Y / Z travel (mm) | 2500 / 1000 / 1000 | 2800 / 1400 / 1400 | 3000 / 1400 / 1400 | 3300 / 1000 / 1000 |
| Worktable (mm) | 2500 × 1000 | 2800 × 1000 | 3000 × 1000 | 3300 × 1000 |
| Machine weight, approx. (kg) | 4200 | 4500 | 4650 | 4400 |
| Overall dimensions, approx. (m) | 3.9 × 2.3 × 2.45 | 4.2 × 2.45 × 2.5 | 4.2 × 2.8 × 2.5 | 4.5 × 2.8 × 2.5 |
Standard supply is AC 380 V, three-phase. Installed power is approximately 9 kW. Machine weights exclude packing. Confirm workpiece support and table load for your block.
The SHG holds the graphite block stationary on a low table. Two independent cutting assemblies move on the gantry, each with its own closed-loop cutting wire. The numbers in the schematic match the component list below.
| Axis | Arrow in schematic | What moves | 機能 |
|---|---|---|---|
| X | Front to back, along the block length | Cutting assemblies travel front to back along the block length; both units share this longitudinal travel. | Squaring, trimming and long straight cuts. |
| Y | Left to right, across the block width (along the beam) | Cutting assemblies move across the width of the workpiece. | Positioning the cut across the width of the block. |
| Z | 縦型 | Vertical travel of the cutting assembly. | Top-down feed for slabbing and separating sections. |
| X + Z | Coordinated motion | Both axes move at the same time under CNC control. | Programmed contour cuts for shaped blanks. |
Share the profile drawing so Vimfun can confirm feasibility and fixture clearance.
m/s. How fast the closed-loop wire circulates around its loop. It is set by the wire drive.
Machine range: 0–50 m/s. Initial window for isostatic and fine-grain graphite: 30–40 m/s.
mm/min. How fast CNC motion advances the cutting assembly relative to the block, which is how fast the cut progresses through the graphite.
Machine range: X 0.01–3000 mm/min; Y and Z 0.01–5000 mm/min. Initial window for isostatic and fine-grain graphite: 50–100 mm/min.
Wire speed is the motion of the cutting tool itself. Feed rate is the motion of the axes. At the initial window, the wire travels roughly 18,000 to 48,000 times farther per minute than the head advances. Raising wire speed does not advance the cut, and raising feed does not make the wire run faster. Set both during commissioning for the actual grade and section size.
Single-mode length matches the X travel of the model. When the horizontal and vertical units work in the same setup, both assemblies share the same X stroke instead of each having the full stroke. The block must therefore fit a shorter envelope. On the standard models, the combined-mode length is 600 to 800 mm below the single-mode length.
A 2,400 × 1,400 × 1,200 mm block requiring both directions puts the SHG300-170 on the shortlist. Its combined-mode length and width match the nominal block size. Confirm usable height, actual stock dimensions and support clearance before selecting it. The SHG330-120 has a 1,200 mm combined-mode width, so this block exceeds its width limit.

Locate the block from a stable datum, check support under the cut-off section, and allow space for dust extraction and handling before the first pass.
Feed the cutting head down through the block to separate slabs or part off sections.
Cut along the block length to trim edges and prepare stock for downstream machining.
Use coordinated X/Z motion to cut a programmed profile for shaped graphite blanks.
これらの画像は、SHG機器の推奨事項からのものです。意図された操作を確認する際には、容量表と併せて使用してください。





送り速度または切断方向を選択する前に、完成したブランクの寸法と機械加工代について合意してください。合意した位置での基準面、エッジの状態、および寸法変動を検査してください。結果の再現性を確保するために、グラファイトグレード、切断方向、およびサポートを記録してください。
一般的な材料には、等方性、押出成形、および微粒グラファイトが含まれます。SHGシリーズはグラファイトを乾式で切断します。切断ゾーンでの集塵を計画し、ブロック寸法に対するワークピースサポートと固定を確認してください。
等方性および微粒グラファイトの場合、初期プロセスウィンドウはワイヤ速度30〜40 m/s、送り速度50〜100 mm/minです。初期ワイヤ径と張力範囲は0.6〜1.0 mmおよび150〜200 Nです。機械のワイヤ速度範囲は0〜50 m/sです。実際のグレードと断面サイズに合わせて、コミッショニング中に生産パラメータを設定してください。
SHG330-120は、単一切断モードで最大3,300 mm長のブロックに対応し、公称エンベロープは3,300 × 1,200 × 1,000 mmです。複合モードの長さ制限は2,500 mmです。
はい。個別の切断ユニットが1つのフレームに取り付けられています。切断計画を確定する前に、選択したモデルの複合モードエンベロープを確認してください。
同期X/Z補間は、プログラムされた輪郭切断をサポートします。実現可能性を確認するために、プロファイル図を共有してください。
SHGグラファイトプロセスは乾式です。切断ゾーンに集塵を提供してください。
X、Y、Zトラベル、ワークテーブルの寸法、固定、および集塵インターフェースは、設置に合わせて仕様を決定できます。
SHG構成について相談する
SHG見積もりをリクエストする